Collins Restoration Notes from WA3DSP
75S1 Receiver Updates HERE
Modernizing the Collins 516F-2 Power Supply
The Collins 516F-2 Power Supply is used to power the Collins 32S transmitters and the KWM2 transceiver. It supplies the 6.3 volt filament, low and high voltage B+, and bias voltages. The original design used a 5R4 vacuum tube rectifier for the high voltage B+ and a 5U4 for the low voltage. The bias supply used an encased selenium rectifier. Mains AC was routed to the transmitter or transceiver where a switch was used to turn the power on.
My 516F-2 was completely stock and in excellent condition. It did not include a speaker. In reviewing the many Internet sites about upgrading and restoring the power supply I decided how I was going to proceed. I wanted to reduce heat, increase efficiency, and improve reliability. One consideration was my local line voltage which is consistently on the high side running an average of about 123 volts but as high as 128 volts at times.
This article is about my upgrade of the Collins 516F-2 power supply. It includes four separate changes which could be made individually or in entirety to make the supply and the equipment it works with more reliable. The changes are:
Being an enthusiast of vacuum tube equipment made before 1970 I have a real concern with elevated line voltages and its effect on this equipment. I did some research on this topic and I found that nominal line voltages increased from something less than 110 Volts in the early 20th century to usually greater than 120 volts today. Several ANSI documents1 describe the dilemma that electrical engineers had with standard voltages in the evolving US electrical system.
If you are a collector of older electronic and electrical equipment like I am then you have more than likely seen equipment labels specifying 110V, 115V, 117V, and 120V as the operating voltage. In the 1950's when the Collins S-line was designed the nominal line voltage was 115V but there is a wide range of minimum and maximum voltages around that nominal value. Today national standards2 classify two ranges. (A) with a range of 110-124.5 volts or roughly +-5% of nominal or (B) with a range of 108-126 volts or roughly -13% to +6% of nominal. Range (A) is considered normal and voltages outside of these limits should be infrequent. The (B) range is considered out of limits if encountered on a sustained basis and corrective action should be taken. There does not seem to be any clarification of the terms infrequent and sustained so I suppose there is some room for interpretation here.
So typical line voltages can be anywhere between 110 and 124.5 volts and be considered normal by your utility. In my practical experience and talking to many other hams line voltages are often on the high side of this range. I have been recording line voltage samples at my home every 10 minutes for several years and looking back through the data my lowest voltage is about 120 and highest about 128 with the average about 124. I would probably have an argument for being in the (B) range in many cases. My line voltage does have fairly good regulation as these numbers do not change substantially from summer to winter or at different times of the day.
So that leads me back to the Collins 516F-2 power supply. I had a KWM2 and recently acquired a 32s1 and 75s1 pair. In measuring the stock supply with no modifications the low B+ when using the KWM2 in receive mode was greater than 290 volts and often close to or slightly more than 300 volts. If you have a KWM2 you and you have puttered around inside after it has been on for awhile you know that many of the tubes run extremely hot. So hot in fact that touching them can cause almost instant burns. I was not happy that the higher B+ and filament voltage were de-rating the life of the tubes, causing additional heat, and generally wasting energy.
I also intended to solid-state the 5U4 and 5R4 rectifiers which with lower voltage drop would add to the problem. So my first modification was to remove the vacuum tube rectifiers and build solid-state replacements on plug in sockets. I then used the former 5 volt filament windings in series to buck the line voltage. This gave me 10 volts less line voltage and with my 124 average line voltage it brought the 516F-2's applied primary voltage within specs. This resulted in filament voltages, measured at the tube socket, of about 6.1 volts AC and well within specs on the low side, just where I wanted it. However the low B+ was still too high. A common fix for this is to add series resistance in the output of the rectifier diodes. This somewhat solves the problem but greatly reduces the regulation. The KWM2 draws significantly more low B+ current on transmit than receive thus adding a resistance that gives a satisfactory receive voltage results in a too low B+ on transmit. The 32s1 is similar. When in standby there is very little B+ draw but the voltage still appears on many tubes and components. Because of this very light load the low B+ can exceed 300 volts by a substantial amount. For me it was just not a good solution.
I scouted around and asked some questions on various forums and I found that Clarence Watts W6BN (now W7ASB) had designed a MOSFET regulator for the 516F-2. I used his design and added a few more safety features. With this regulator you can set the low B+ to whatever you want. Collins specifies +275 volts but I choose +270 for my supply and it works well with both my KWM2 and the 32s1. I did add an additional 100 ohm series resistor off of the diode rectifiers which I located in the bleeder cage on the top of the chassis. To change the output voltage you select the reference zener voltage applied to the MOSFET gate. In my case I used two 100 volt and one 75 volt zener in series. Using this regulator results in the B+ being within a few volts of the set voltage independent of the load. The equipment never sees more than 270 Volts.
I did not pay much attention to the high B+ as this is much less critical and would be impractical to regulate. The parallel resonant circuit of L1 and C1 (.05ufd) is meant to somewhat regulate the loaded to no load voltage. Theoretically at 60hz the parallel resonance happens at no load or just bleeder load and results in a reduced output voltage. In my tests this was the case. Without C1 the no load high B+ was well over 1000 volts. With it installed it measured around 900 volts. C1 is often removed after a failure as an unnecessary part but without it the stresses on the high B+ components could result in a failure. If you are using the supply on a 50hz line the value of C1 would need to be changed.
The bias voltage selenium rectifier was replaced with a diode rectifier.
I also wanted to eliminate the high AC current through the connection to the rig and its AC power switch. I reviewed a number of methods to accomplish this. Most involved relays and power sources that need to be on all the time. Some used a 120 volt mechanical relay to switch the power. This was probably the simplest approach but since I did not have a 120 volt AC coil relay I decided to go in a different direction. I did have a number of solid-state relay (SSR) modules on hand. They were rated at 12 amps and required anywhere from 3 to 30 volts DC at about 10 ma. to operate.
The module as you can see in the photo fits nicely in the area where C1, the HV choke resonating capacitor, had been mounted. C1 was remounted on the front right side of the chassis. It is a replacement glass high voltage capacitor with heat shrink tubing over it. The circuitry includes a resistor, diode, capacitor, zener diode, and the SSR module. SSR’s have very high isolation between the switching and switched terminals but in this circuit the AC is NOT isolated. I did not want to use a separate power source which would be on all the time so instead I opted to directly rectify and filter the line to drive the SSR through the switch in the rig. This greatly reduces the current through the rigs power switch from amperes of current to less than 20 ma. and when the power switch is off there is no current flow from the AC line. The series resistor needs to be selected based on the turn-on current requirements of the selected SSR.
Because there is high voltage present around the solid state rectifiers and regulator I installed an aluminum plate on the back right opening of the case as protection. In a discussion wiith Bill Carnes he mentioned that there was often a heat problem with the 516F-2 power transformer and that possibly this plate would interfere with airflow. I did not see a problem with that as there is ample opening on the outter case and the rear is still well opened. I did however find that the after awhile the bleeder resistor cage in the back emitted a great deal of heat. While the majority of this radiated upwards the cage is right up against the power transformer and appeared to considerably heat the back side. I experimented with a small 12 volts computer size muffin fan mounted blowing out on the back of the cage and running on about 6-7 volts DC. It worked very well in keeping the cage cool and was extremely quiet. I permanently mounted it with two 4-40 screws, nut side out, to the back of the cage. Power was procured from the 6.3 VAC bus a half wave diode rectifier and a small filter capacitor.
The completed supply works very well with both my KWM2 and 32s1 and I am happy knowing that they have a constant and reasonable B+ voltage. While I am sure there are many who are abhorred by the thought of making any changes to this classic equipment this is certainly your choice. I just wanted to raise the awareness that using this power supply or other classic equipment on today's power grid without some means of voltage compensation could lead to premature failure of associated components. If you do nothing else use an external variac or buck transformer to ease the problem.
Simplified schematic of the power-on modifications. Refer to the complete modification schematic for more detail.
This supply still has the original electrolytic filter capacitors which are working fine but if and when they need replacement I will likely replace the three 30uf/400 volt high voltage stack with three 100uf/450 volt replacements. The higher values are now smaller than the original 30uf capacitors. I would do the same in the low voltage supply replacing the 15uf and 30uf capacitors with 100uf 450 volt values.
Links to other WA3DSP Sites
© 2012 WA3DSP